Made In Great Britain

Direct from our factory

Free Next Day Delivery

On orders over £750

Product Test Results

All test results published

Expert Technical Advice

Call or chat with our team

EverFlor · Floor Repair

TarmaFix® Flow

TarmaFix Flow is a pourable, fibre-reinforced repair mortar for contractors and site owners fixing potholes and worn areas in tarmac and asphalt. Mix it, pour it into the prepared hole, and it flows level into the damage with little trowelling and no compaction.

WHAT YOU GET
✓ Self Levelling Pour — Flows Into The Repair✓ Forklift Ready — Industrial Grade Strength✓ Internal & External — Indoor & Outdoor Use✓ Damp Tolerant — Apply to Damp Surfaces✓ Deep Repair — Fills Up To 100mm In One Pour✓ Foot Traffic Ready — Walk On After 30 Minutes
25kg
2.404,00 kr/ 25kg inc VAT
Out of stockOrder by 11am → dispatched todayFree delivery over £750
Open a trade account
ON SITE
30 minutes
foot traffic — at 20°C
2 hrs
forklift ready — at 20°C
5-10 minutes
pot life — at 20°C
Sequence: prepare the repair area → measure and mix → pour straight away → spread and finish → let it cure.
TarmaFix® Flow 25kg
Out of stock 2.404,00 krinc VAT / 25kg
2.404,00 kr inc VAT / 25kg 25kg

WHAT IT IS, HOW TO USE IT: Pour-in cementitious mortar for potholes and worn tarmac or asphalt

DESCRIPTION

TarmaFix Flow is a pourable tarmac repair mortar for potholes, depressions and eroded areas in asphalt and tarmac. It is a fibre-reinforced, polymer-modified cement powder. Mixed with clean water, it becomes a fluid mortar that runs into the damaged area and settles level under its own weight.

This is not a bituminous cold-lay product. Cold-lay tarmac has to be tamped or rolled to compact it. TarmaFix Flow needs no compaction: pour it in, let it settle, and finish with a steel float where needed. The polymer improves bond to the existing surface. The fibres reinforce the cured mortar against cracking and wear.

It fills damage up to 100mm deep in a single pour. Deeper holes are built up in layers. It sets fast, so a car park, yard or loading area returns to use within hours rather than days. It also bonds to concrete, so one product covers asphalt, tarmac and concrete patches on the same site.

Recommended areas of use

  • Car parks
  • Driveways
  • Loading bays and access routes
  • Paths and walkways
  • Industrial yards
  • Internal asphalt floors
  • Potholes, depressions, dished areas and surface erosion in external tarmac
  • Patch repairs to concrete

Features

  • Pourable consistency: the mortar runs into the hole and finds its own level, so there is no compaction and little trowelling.
  • Fibre reinforcement throughout the mix holds the cured repair together under traffic and resists cracking.
  • Polymer-modified cement bonds to asphalt, tarmac and concrete without a separate primer in the specification.
  • Rapid set: foot traffic and forklift traffic return on the same day, which keeps downtime short.
  • No heating and no hot-asphalt plant: mix and pour from a bucket on site.
  • Applies to damp substrates, so a repair can go ahead after rain once standing water is cleared.
  • Interior and exterior use.
  • Low VOC content, below 30 g/l, and tools clean with water before the mortar hardens.

Good to know

  • The cured repair is dark grey and cementitious. It will not match the black of surrounding tarmac, and it is rigid rather than flexible.
  • Do not apply to newly laid asphalt. Fresh asphalt carries surface oils and still moves, which can weaken the bond and crack a rigid repair. Let new surfaces age before repairing them.
  • The substrate must be sound. Do not pour over loose or unstable asphalt.
  • Damp is acceptable. Standing water is not.
  • The mortar relies on flow, so the repair area needs to be reasonably level. Do not use it on steep slopes or vertical faces.
  • Pot life is short. Mix beside the repair and only mix what you can place straight away.
  • Edges can be feathered to blend into the surrounding surface, but the thinnest edges do not carry the strength of the full-depth repair.
  • Cure times lengthen in cold weather and vary with repair depth and site conditions.
  • Shelf life is 12 months. Store between 5°C and 30°C.

APPLICATION

SURFACE PREPARATION

The asphalt, tarmac or concrete must be sound and stable. Do not pour over loose or moving asphalt. Do not repair newly laid asphalt; let it age first, as fresh surfaces carry oils and still move.

Sweep out all loose material, dust and dirt with a stiff broom or brush. Scrape out oil and grease, or treat it with a degreaser. Remove standing water. The surface can be damp but not saturated.

The repair area needs to be reasonably level so the mortar can flow into it. Do not use on steep slopes or vertical faces.

MIXING

Mix close to the repair. Pot life is approximately 5-10 minutes at 20°C, so only mix what you can pour within that time. Keep a bucket of clean water nearby for rinsing tools.

Measure clean, cold water into the mixing bucket to the ratio on the product label. Add the powder gradually, stirring continuously. Use a mixing blade in an electric drill for larger batches. Mix until smooth, evenly coloured and pourable. Use immediately. Do not add thinners.

APPLICATION

Apply between 5°C and 30°C. Pour the mortar directly into the prepared hole and let it settle. Use a steel float or trowel to spread it across wider areas and to finish the surface. Feather the edges to blend with the surrounding surface.

For holes deeper than a single layer allows, build up in layers. Let each layer cure before placing the next. On broad, worn areas, keep a consistent thickness across the patch rather than skimming it to nothing.

CURING AND RETURN TO SERVICE

Full cure takes 3 hours at 20°C. Lower temperatures, deeper repairs and damp conditions extend this. Keep vehicles off until the repair has hardened. Wash tools with water before the product dries.

PERFORMANCE: Built for punishment.

What the cured film withstands — anchored to the published test results, never to adjectives. Anything not yet rated says so, plainly.
Rapid cureForklifts back on the repair the same dayForklift Ready: 2 hours at 20°C. Full cure: 3 hours at 20°C. A yard or loading bay closes for a few hours, not days.Lower temperatures, deeper repairs and damp conditions extend these times.
Fill depthFills up to 100mm deep in one pourDepth: 100mm in a single layer. Fill a pothole or dished area in one go. It needs no compaction in lifts.
AdhesionBonds to asphalt, tarmac and concreteSuitable substrates are asphalt and tarmac, and it can also be used on concrete. The polymer-modified cement bonds without a separate primer in the specification.The substrate must be sound, stable and free of oil and grease.
ReinforcementFibres hold the repair togetherFibre-reinforced polymer and cement composition. The fibres run through the whole mix. They hold the cured repair together under traffic and resist cracking.

SUITABILITY: Where it belongs.

Environments this product is right for — with the condition or variant where one applies — and, just as plainly, what it is not for.
ENVIRONMENTS
Car parks Bonds to asphalt and tarmac and suits exterior use. Potholes in parking bays fill in place.RATED
Driveways Pours into depressions in tarmac drives and is suitable for exterior use.RATED
Loading bays and access routes Takes forklift traffic once cured, so a bay or route reopens the same day.RATED
Industrial yards One product repairs asphalt, tarmac and concrete patches across the same yard.RATED
Paths and walkways Takes foot traffic once cured. A damp surface is acceptable once standing water is cleared.RATED
Internal asphalt floors Suitable for interior use as well as exterior, on asphalt substrates.RATED
Concrete patch repairs Concrete is a listed substrate alongside asphalt and tarmac.RATED
Potholes in external tarmac Pours into potholes, dished areas and eroded tarmac and settles level.RATED
TRAFFIC TOLERANCE
Foot trafficFoot traffic: 30 Minutes at 20°C.RATED
Forklift trafficForklift Ready: 2 hours at 20°C.RATED
NOT FOR — AND NOT YET RATED
Not for newly laid asphalt. Fresh surfaces carry oils and still move, which weakens the bond and can crack a rigid repair. Let new tarmac age first.Not for loose or moving asphalt. The substrate must be sound and stable before you pour.Not for steep slopes or vertical faces. The mortar relies on flow, so the repair area must be reasonably level.Not for pouring into standing water. Damp is acceptable; sweep or sponge out puddles first.Not for application outside 5-30℃. Hold the job until conditions are within that window.

Two Component System: One unit. Two parts. No guesswork.

All parts arrive pre-weighed in one unit at a See product label mix ratio — no measuring on site.
Part A Fibre-reinforced polymer cement powderSee product label parts by weightPart A: fibre-reinforced polymer and cement powder. It forms the body of the repair.
+
Part B Clean, cold waterPart B: clean, cold water. Measure it to the label ratio and pour it in first.
=
MIXED UNIT5-10 minutes pot lifeat 20°CSets to a rigid repair. Pot life approximately 5-10 minutes at 20°C: mix only what you can pour.

APPLICATION: Step by step.

01 Prepare the repair area Sweep out loose asphalt, dust and debris with a stiff broom or brush. Scrape away oil and grease, or remove it with a degreaser. Clear any standing water; a damp surface is acceptable.
02 Measure and mix Pour the measured clean, cold water into a mixing bucket first. Add the powder gradually while mixing continuously, using a mixing blade on an electric drill for larger quantities. Stop when the mix is smooth, evenly coloured and pourable.
03 Pour straight away Pour the mortar into the damaged area immediately after mixing. Let it flow and settle into the hole. Mix the next batch only when you are ready to place it.
04 Spread and finish Use a steel float or trowel to push the mortar into corners and level it where it has not self-levelled. Feather the edges into the surrounding surface. Wash tools in water before the mortar hardens.
05 Let it cure Keep traffic off until the repair has cured. Allow longer in cold weather and on deep repairs.
KNOW BEFORE YOU BUY
Pot life is approximately 5-10 minutes at 20°C. Mix only what you can pour within that time.The mixing ratio is on the product label. Measure the water to that ratio before adding powder.Build deeper holes up in layers. Let each layer cure before pouring the next.Feathered edges are weaker than the full-depth repair. They blend the patch in but do not carry its strength.Cure times lengthen with cold, depth and damp. Full cure is 3 hours at 20°C, and longer below that.The finish is dark grey. It is a rigid cementitious repair, not a flexible bitumen one.Do not add thinners. Apply as supplied, mixed with clean water only.Shelf life is 12 months. Store between 5-30℃.

WORKING DATA: The numbers you plan a job around.

Technical data
EverFlor - TarmaFix® Flow — technical data
FinishDark grey
CoverageApproximately 0.5m2 at 25mm thick
Recommended coats1
Full cure3 hours at 20°C
ApplicationSteel float or trowel. A mixing blade fitted into an electric drill helps with mixing
Cleaner / ThinnerNot required — apply as supplied
Suitable substratesAsphalt, Tarmac and can also be used on concrete
Shelf life12 months
VOC content< 30 g/l
Cleaning toolsWash with water before the product dries
Foot traffic30 Minutes at 20°C
Composition2 part, Fibre reinforced polymer, and cement based dark grey powder
Depth100mm
Forklift Ready2 hours at 20°C

FAQS: Straight answers.

Can I use TarmaFix Flow on newly laid tarmac?

No. New asphalt still carries surface oils and remains mobile while it settles. Both reduce adhesion, and movement can crack a rigid cementitious repair. Let new tarmac age before repairing it, and only repair surfaces that are sound and stable.

Does the surface have to be dry?

No. TarmaFix Flow can go onto damp asphalt, tarmac or concrete. It cannot go into standing water, so sweep or sponge out any puddles first. The surface must also be free of loose material, dust, oil and grease. Scrape out heavy contamination or treat it with a degreaser.

How deep a hole can I fill?

Pour up to 100mm deep in one layer. For deeper holes, build up in layers no thicker than that, and let each layer cure before pouring the next. Edges can be feathered to blend into the surrounding surface, but the thinnest edges do not carry the strength of the full-depth repair.

How soon can people and vehicles use the repaired area?

Foot traffic can return after 30 minutes at 20°C. Allow longer before vehicle and forklift traffic. All times extend in cooler weather and on deeper repairs, so check the repair has hardened before reopening the area.

How much do I need?

Coverage is approximately 0.5m² at 25mm thick. Coverage scales with depth: at 50mm, expect roughly half that area. Measure the hole's area and average depth, then add an allowance for an uneven base and wastage. Because the pot life is short, plan the job in batches you can pour straight away.

TECHNICAL SUPPORT Speak to a coating specialist

0800 043 8220 — advice from the people who formulate it.

DISPATCH Same-day before 11am

Order by 11am and it ships today, straight from the Tuxford factory floor.

DIRECT FROM MANUFACTURER Made, tested, dispatched

One UK site, no middlemen — the batch you get is the batch we tested.

DELIVERY UK & mainland Europe

Free next-day delivery on orders over £750.

QUOTE / PO

Request a quote or raise a PO

Tell us what you need and where it's going. We'll reply with a written quote you can raise a purchase order against.

For: TarmaFix® Flow — 25kg