Fabriqué en Grande-Bretagne

Directement de notre usine

Livraison gratuite le lendemain

Pour toute commande supérieure à 750 £

Résultats du test produit

Tous les résultats des tests publiés

Conseils techniques d'experts

Appelez ou discutez avec notre équipe

Cliquez sur une icône pour explorer les fonctionnalités Appuyez sur une icône pour explorer les fonctionnalités
EverFlor - Prime OT container, background removed

Measured Mix Window

Mix base and hardener at 1.76:1 by weight and the film cures by chemical reaction, not by drying. Pot life is up to 45 minutes at 20°C, so mix only what you can brush out in that window. Nothing is thinned; apply the material as supplied between 10°C and 25°C.

Sealed Absorbency Coat

Absorbent concrete draws binder out of a finish coat, leaving uneven gloss and weak adhesion. One coat at 3-4m² per kg seals that absorbency, so the EverFlor finish that follows cures with even gloss and full adhesion. Apply by medium pile roller and cut in with a brush.

Zero Loss Penetration Cure

The resin is 100% solids, so nothing flashes off as solvent and everything applied stays in and on the floor. The material soaks into open concrete and cures within the top layer, consolidating it instead of bridging over it. A 220 micron wet film stays a 220 micron dry film.

Residual Oil Tolerance

Porous concrete draws oil below the surface over years of workshop use. Degreasing and grinding remove what you can see, but residue stays in the pores and can stop a conventional epoxy primer bonding. Prime OT is formulated to tolerate that residual oil in prepared concrete; remove all visible oil and grease first, then degrease and mechanically prepare the floor before priming.

Profil de performance

Two-Pack 100% Solids Epoxy. Prime OT is an oil tolerant primer for porous concrete that has been degreased and mechanically prepared. Resin and hardener cure by chemical reaction, so the film you lay down is the film that stays. It seals the slab and gives the following EverFlor coating a stable base.

Télécharger la fiche technique
Coverage 3-4m²per kg
Pot Life 45 minutesat 20°C
Touch Dry 6 hrsat 20°C
Film Thickness 220 micronswet and dry

Informations essentielles

Détails du produit

Description

EverFlor Prime OT is an oil tolerant epoxy floor primer for concrete that has previously been exposed to oil, grease or lubricants. It is built for the floors that oil soaks into over years of use: vehicle workshops, garages, MOT bays and industrial units. Apply it after thorough degreasing and mechanical preparation. It seals the prepared slab and gives the following coat a stable base.

Porous concrete absorbs oil below the surface. Degreasing and grinding remove what you can see, but residue stays in the pores. That residue is the usual reason a conventional epoxy primer fails to bond. Prime OT is formulated to tolerate this residual contamination in prepared concrete. It does not tolerate visible oil, standing grease or unprepared floors.

Prime OT is a 100% solids, two-component epoxy resin. The resin and hardener cure by chemical reaction rather than by evaporation. VOC content is below 30 g/l. Overcoat it with a compatible EverFlor floor coating system once it has cured to the recoat stage.

Recommended areas of use

  • Vehicle workshops and garages
  • MOT bays and maintenance bays
  • Engineering workshops and industrial units
  • Machinery areas and plant rooms
  • Porous concrete floors previously exposed to lubricants or hydraulic oils
  • Absorbent concrete that needs stabilising before coating, inside or outside

Features

  • Oil tolerant formulation: designed for concrete with historic oil contamination that remains in the pores after cleaning.
  • Two-component epoxy: resin and hardener react to form a cross-linked film, so it cures by chemistry rather than by drying out.
  • No thinning: supplied ready to apply once mixed, so the mix you apply is the mix the factory formulated.
  • Seals porous concrete: stabilises absorbent slabs so the floor coating above cures on a consistent surface rather than soaking in unevenly.
  • Grey film: the primed floor is easy to inspect for missed areas before the coating goes on.
  • Interior and exterior: suitable for concrete floors inside buildings and outdoors.
  • Low VOC: keeps solvent odour down in enclosed workshops during application.

Good to know

  • Oil tolerant does not mean you can prime over oil. Remove all visible oil and grease first.
  • Degrease thoroughly, then grind or abrade. Mechanical preparation removes the contaminated top layer and gives the primer a key.
  • If oil continues to migrate back to the surface after preparation, clean again or assess the substrate before priming.
  • Deeply saturated concrete may need repeated degreasing and removal of affected material.
  • Overcoat the primer with a compatible EverFlor floor coating. It is a primer, not a finished floor.
  • Cure and working times shorten in warm conditions and lengthen in cold ones.
  • Full cure takes 7 days. Shelf life is 24 months stored between 10°C and 25°C.
Application

SURFACE PREPARATION

Oil tolerance does not replace preparation. Remove all loose dirt and debris. Degrease the floor with a suitable heavy-duty degreaser. Repeat until no visible oil or grease remains. Rinse away degreaser residues and let the floor dry.

Grind, abrade or otherwise mechanically prepare the slab. This removes the contaminated top layer and gives the primer a key. Vacuum away all dust and loose material. If oil continues to migrate back to the surface, clean again or assess the substrate before you prime.

MIXING

Prime OT is a two-component system mixed at 1.76 : 1 by weight (A:B). Stir Part A first. Add the complete Part B. Mix mechanically with a slow-speed paddle until uniform, scraping the sides and base of the tin. Do not add thinners.

APPLICATION

Apply between 10°C and 25°C. Cut in edges and corners with a brush. Roll the main area with a medium pile roller, working the primer into the concrete. Apply one even coat and avoid leaving ponds in hollows. Clean tools in warm soapy water straight after use.

OVERCOATING

At 20°C, apply the EverFlor floor coating after 8 hours and within 48 hours. Beyond 48 hours, abrade the primed surface before coating. Allow 7 days for full cure.

Le Centre de Connaissances

Tout ce que vous devez savoir

Parcourez notre collection d'articles détaillés et de guides pratiques conçus pour vous aider à tirer le meilleur parti de ce produit. Que vous ayez besoin d'aide pour la préparation des surfaces ou de conseils d'application, nous avons ce qu'il vous faut.

Afficher le Centre technique

A visual comparison of a mossy, weed-infested block paving driveway next to a freshly cleaned section in the UK.
  • par Sam Marriott

Restauration de pavés autobloquants : Élimination de la mousse, des mauvaises herbes et du lichen

Le pavage est le choix le plus populaire pour les allées au Royaume-Uni, mais il présente un défaut de conception majeur : Les joints. Ces milliers d'espaces entre les briques sont le terreau idéal pour les mauvaises herbes, la mousse...

Plus

An unbranded industrial floor scrubber being used to maintain the high-gloss shine on a polished concrete warehouse floor.
  • par Sam Marriott

Nettoyer en profondeur le béton poli sans ternir sa brillance

Le béton poli est souvent vendu comme l'option de revêtement de sol "sans entretien". C'est un mensonge. Oui, il est incroyablement durable. Il ne s'écaillera pas comme de la peinture. Mais si vous l'ignorez, ou pire – si vous le...

Plus

Two unbranded silver tins labeled Acid and Alkaline on an industrial concrete warehouse floor.
  • par Sam Marriott

Nettoyants pour béton acides ou alcalins : Lequel est le meilleur pour votre sol ?

Si vous entrez dans une quincaillerie et demandez un "nettoyant à béton", vous vous retrouverez probablement avec plusieurs options devant vous. La plupart des gens choisissent la bouteille avec l'étiquette d'avertissement la plus agressive, pensant que "plus c'est fort, mieux...

Plus

How to Sand a Painted Concrete Floor for Recoating
  • par Sam Marriott

Comment poncer un sol en béton peint avant de le repeindre

Dans notre guide Ponçage vs. Meulage : Préparation du béton précédemment peint, nous avons établi que si votre sol réussit le test d'adhérence par quadrillage, l'étape suivante pour un nouveau revêtement sera le ponçage. Choisir de poncer plutôt que de meuler vous fait économiser des centaines de livres...

Plus

FAQ

Veuillez consulter notre page FAQ pour en savoir plus.

Can I apply Prime OT directly over an oily floor?
No. Prime OT tolerates residual oil held in the pores of concrete that has been cleaned and prepared. It does not bond over visible oil, grease, standing liquids or unprepared floors. Degrease until no visible contamination remains, then grind or abrade the surface before priming.
What preparation does an oil-contaminated floor need?
Remove loose debris, then degrease with a heavy-duty degreaser, repeating until visible oil and grease are gone. Rinse off residues and let the floor dry. Grind or abrade to remove the contaminated top layer and create a key, then vacuum all dust. If oil keeps returning to the surface, clean again or have the substrate assessed before priming.
How much floor does a 5kg unit cover?
Coverage is 3-4m² per kg, so a 5kg unit primes roughly 15-20m² in a single coat. Very porous or heavily ground concrete sits at the lower end of that range.
When can I apply the floor coating?
At 20°C, overcoat after 8 hours and within 48 hours. Light foot traffic is possible after 8 hours. If you miss the 48-hour window, abrade the primer before coating. Colder conditions extend these times.
Can I use it outdoors, and in what temperatures?
Yes. Prime OT is suitable for interior and exterior concrete floors. Apply it between 10°C and 25°C, and do not apply below 10°C. Store unopened units between 10°C and 25°C.

Vous n'avez pas trouvé votre réponse ?

N'hésitez pas à nous contacter